Once drywall goes up, everything that makes a house work disappears behind a smooth white surface. The framing, the wiring, the supply lines, the drain pipes, and the insulation are all still there, but nobody can see them again without cutting into the wall. A pre-drywall inspection is the short window when a buyer can have a qualified person look at every one of those components while they are still exposed. For anyone building in Frisco, where new neighborhoods keep expanding north along the Dallas North Tollway, that window is worth protecting.
At TrueMark Inspections we approach this stage the way a builder would, because our lead inspector is a licensed general contractor who has worked on more than fifty renovation and flip projects. He has been the person who has to fix mistakes after the walls are closed, and that experience shapes everything we look for at this stage.
What We Look at During the Framing Stage
Framing is the skeleton of the home, and small problems here travel through the whole structure. We look at how studs, headers, and beams are connected, whether load paths make sense, and whether any members were notched or drilled in ways that weaken them. We check for splits, warping, and missing fasteners. We also look at how the roof framing ties into the walls, because a home in North Texas has to handle strong spring storms and sudden wind events.
Window and door openings get close attention too. If a rough opening is out of square or lacks proper support, the problem shows up later as sticking doors, cracked trim, and drafts. Catching it now means a framer fixes it in an afternoon. Catching it after drywall and paint means a much more expensive repair.
Plumbing, Electrical, and HVAC Rough-Ins
The rough-in stage is where a pre-drywall inspection earns its fee. We look at supply lines for proper support and protection where they pass through framing, and we check drain and vent lines for slope and connection quality. Electrical boxes should be set at consistent heights and securely mounted, and cables should be stapled and protected where required. We look for wires running too close to the edge of studs where a drywall screw could later pierce them.
Ductwork gets the same scrutiny. Loose connections, crushed runs, and poorly sealed joints waste energy and leave rooms uncomfortable for years. In a Texas summer, a duct system that leaks into the attic can make a brand new home feel like it has a failing air conditioner.
Insulation, Moisture Barriers, and Fire Blocking
Before the walls close, we also look at the details that protect the home from heat, water, and fire. Fire blocking should be in place where it is needed, and penetrations through framing should be sealed. Flashing around windows and doors should be installed in a way that sheds water outward. Missing or sloppy flashing is one of the most common reasons moisture finds its way into wall cavities, and it rarely shows itself until mold or rot has already started.
How This Differs From the City’s Inspections
Many buyers assume the city already handles this. The City of Frisco’s building inspections division does perform its own structural inspections of new construction, and it publishes the requirements on its Residential Inspections Checklists page. Those inspections confirm that work meets code at specific milestones. They are not written for the buyer, and they are not a substitute for an independent review. Our review works for you, and it often finds workmanship issues that technically pass code but still deserve attention.
What You Receive After the Inspection
Our reports are photo-rich, and you receive them within 24 hours. Each finding is documented with images and written in plain language, so you can hand it to your builder or project manager and have a clear conversation about what needs to be corrected. Because our inspector has a contractor’s background, we also explain why an item matters and what a reasonable fix looks like, which helps buyers have productive conversations without turning every punch list item into a dispute.
When to Schedule
The best timing is after the rough-ins are complete and before insulation and drywall are installed. Builders move quickly at this stage, so it helps to book early and confirm the timing with your site supervisor. If you are building in Frisco or anywhere in the surrounding area, schedule your pre-drywall inspection with TrueMark Inspections and see what is inside your walls while you still can.
Frequently Asked Questions
When should a pre-drywall inspection happen?
It should take place after framing, plumbing, electrical, and HVAC rough-ins are finished and before insulation and drywall are installed. Ask your builder for the schedule so the inspection fits the gap.
How long does it take?
Most take a couple of hours depending on the size and complexity of the home. Larger floor plans with multiple stories or extensive mechanical systems can take longer.
Do I still need a final inspection after this one?
Yes. The two serve different purposes. This stage covers what will be hidden, while a final inspection covers finished surfaces, appliances, and operating systems. Many Frisco buyers also add an 11th-month warranty inspection.
Will my builder allow a pre-drywall inspection?
Most builders allow it when it is requested in advance, since many contracts permit buyer inspections at stages of construction. Check your contract and give your builder notice so the visit goes smoothly.
Service Areas: TrueMark Inspections serves McKinney, Frisco, Plano, Allen, Prosper, Celina, Melissa, Fairview, and the greater Dallas-Fort Worth Metroplex.